Wednesday, March 24, 2010

we at vardhman bearings

make all type of universal joints and we make the universal joints under the brand name of oriZin , oriZin brand universal joints , we make ball type , pin type , complete harden , spline joint , telescopic type and with needle bearings type universal joints

please visit below link for same

http://www.vardhmanbearings.com/universal_joints.htm

We introduce our self as manufacturer of all type of universal joints
These universal joints also named as u joint , cross joint , cardon shafts , ball joints , hooke joints , hook joints , hardy spicer joints , cardon joints , consant velocity joint , telescopic universal joints , ball type universal joint , universal joint with spline attachment , universal joint with needle bearings , hook type universal joint , steering joints , steering universal joints , textile joints , machine joints , end joints , hinged joints , universal couplings , fexible couplings , universal joints , u joints , cardon shafts , propeller joints , propeller shafts , universal propeller shafts , hinged universal coupling , cross joints , constant velocity universal joints , trunnion joints , cv joints , billet joints , car universal joints , robot joints , shaft joints , Bendix-Weiss universal joint , tradelink joints , heavy duty universal joints , front universal joints , rear universal joints , cardan universal joints , double universal joints , single universal joint , yoke joint , yoke universal joint , universal joint kit , spider joints , spicer joints , trasmil joints , Steering Column Universal Joint , lovejoy universal joints ,Speed Rzeppa Universal Joint , rear end joints , extended joint , extended universal joint , chrome universal joint , propshaft universal joint , rather crude universal joint , federal mogul universal joint , servo actuator universal joint , driven joints , driven universal joints , drive shaft universal joint , apex universal joints , vardhman universal joints , Johnson power universal joints , steering universal joint , speeder universal joints , angle joints , angle universal joints , gear hub joints , gear hub universal joints , lego universal joints , universal coupling joints , axle universal joints , axle u joint , end yoke joints , uj joints , uj universal joints , u joints , u joints universal joints , ball socket joints , ball socket universal joint , weaver leaver universal joint , ronstan flexible universal joint , ina universal joint , u bolt joint , u bolt universal joint , alignment joint , alignment universal joint , socket joints , socket universal joints , tradelink universal joint , cross and cup universal joint , keyway joints , rod end bearings , rod end universal joint , clevis joints , heim joints , hiem joints ,

We manufacturer all type of universal joints , hook type universal joint , pin type universal joint , ball type universal joint , needle bearing type universal joint , universal joint with needle bearing , telescopic universal joint , harden universal joint , universal joint with spline attachment , universal joint with square bore , universal joint hex bore , universal joint keyway , as per customer requirement , universal joint for high speed , universal joint for high rpm , heavy duty universal joint , light duty universal joint , plastic universal joint , stainless steel universal joint , ss universal joint , stainless steel universal joint , flexible universal joint , cardon shaft universal joint , pin type universal joint , welded universal joint , double universal joint , double universal joint with spline , single universal joint ,


U joint, Cardan joint, Hardy-Spicer joint, or Hooke's joint is a joint in a rigid rod that allows the rod to 'bend' in any direction, and is commonly used in shafts that transmit rotary motion. It consists of a pair of hinges located close together, oriented at 90° relative to each other, connected by a cross shaft.These Universal joint are manily used in automobile , textile , machines , weaving machines , packing machines , spm , filling machines , looms , steering , mills , milling machines , automatic machines , box making machines , construction machines , mining machines , drilling machines , multi spindle drilling machines , rubber machines , packing machines , printing machines , machines , welding machines , cnc machines , cnc lathe , cnc drilling machines , plastic machines , injection machines , laboratory equipments , chemical plants , heavy industry , construction machines , cement plants , cement filling palnts , bottling plants , hydraulic machine , pneumatic machine , rolling mills , robots , cars , assembling machines , material handling machines , steering machines , fixing machines , ATM , fax machines , reactors , trackters , trackter , truck , bulldozer , road macking machines , road marking machines , drilling machines , concert mixing machines , mixtures , rotary machines , spm , agricultural machines , farming machines , poultry machines , automatic machines , gaming machines , gambling machines , building machines , weaving machines , welding machines , weighting machines , weighing machines , grinding machines , switchgear , wire machines , r and d machines , laboratory machines , hardening machines , furnaces , looms , rotary machines , propeller machines , air crafts , marking machines , vending machines , washing machines , virtual machines , crazy machines , complex machines , yard machine , lfiting machines , cranes , slot machines , marking machines , broaching machines , casting machines , forging machines , cigarette making machines , candy making machines , block making machine , soda machines , fog machines , sewing machine ,

Saturday, March 13, 2010

www.vardhmanbearings.com
91-22-28627454
tel/fax: 91-22-28653894 , 28656188
cell : 9892432411 , 9819824531
email : jigesh2007@hotmail.com
vardhmanbearings@rediffmail.com


A bearing is a device to allow constrained relative motion between two or more parts, typically rotation or linear movement. Bearings may be classified broadly according to the motions they allow and according to their principle of operation as well as by the directions of applied loads they can handle. Overview
Plain bearings use surfaces in rubbing contact, often with a lubricant such as oil or graphite. A plain bearing may or may not be a discrete device. It may be nothing more than the bearing surface of a hole with a shaft passing through it, or of a planar surface that bears another (in these cases, not a discrete device); or it may be a layer of bearing metal either fused to the substrate (semi-discrete) or in the form of a separable sleeve (discrete). With suitable lubrication, plain bearings often give entirely acceptable accuracy, life, and friction at minimal cost. Therefore, they are very widely used.
However, there are many applications where a more suitable bearing can improve efficiency, accuracy, service intervals, reliability, speed of operation, size, weight, and costs of purchasing and operating machinery.
Thus, there are many types of bearings, with varying shape, material, lubrication, principal of operation, and so on. For example, rolling-element bearings use spheres or drums rolling between the parts to reduce friction; reduced friction allows tighter tolerances and thus higher precision than a plain bearing, and reduced wear extends the time over which the machine stays accurate. Plain bearings are commonly made of varying types of metal or plastic depending on the load, how corrosive or dirty is the environment, and so on. In addition, bearing friction and life may be altered dramatically by the type and application of lubricants. For example, a lubricant may improve bearing friction and life, but for food processing a bearing may be lubricated by an inferior food-safe lubricant to avoid food contamination; in other situations a bearing may be run without lubricant because continuous lubrication is not feasible, and lubricants attract dirt that damages the bearings

There are at least six common principles of operation:
plain bearing, also known by the specific styles: bushings, journal bearings, sleeve bearings, rifle bearings
rolling-element bearings such as ball bearings and roller bearings
jewel bearings, in which the load is carried by rolling the axle slightly off-center
fluid bearings, in which the load is carried by a gas or liquid
magnetic bearings, in which the load is carried by a magnetic field
flexure bearings, in which the motion is supported by a load element which bends.


Motions
Common motions permitted by bearings are:
Axial rotation e.g. shaft rotation
Linear motion e.g. drawer
spherical rotation e.g. ball and socket joint
hinge motion e.g. door, elbow, knee
[edit] Friction
Reducing friction in bearings is often important for efficiency, to reduce wear and to facilitate extended use at high speeds and to avoid overheating and premature failure of the bearing. Essentially, a bearing can reduce friction by virtue of its shape, by its material, or by introducing and containing a fluid between surfaces or by separating the surfaces with an electromagnetic field.
By shape, gains advantage usually by using spheres or rollers, or by forming flexure bearings.
By material, exploits the nature of the bearing material used. (An example would be using plastics that have low surface friction.)
By fluid, exploits the low viscosity of a layer of fluid, such as a lubricant or as a pressurized medium to keep the two solid parts from touching, or by reducing the normal force between them.
By fields, exploits electromagnetic fields, such as magnetic fields, to keep solid parts from touching.
Combinations of these can even be employed within the same bearing. An example of this is where the cage is made of plastic, and it separates the rollers/balls, which reduce friction by their shape and finish.
[edit] Loads
Bearings vary greatly over the size and directions of forces that they can support.
Forces can be predominately radial, axial (thrust bearings) or Bending moments perpendicular to the main axis.
[edit] Speeds
Different bearing types have different operating speed limits. Speed is typically specified as maximum relative surface speeds, often specified ft/s or m/s. Rotational bearings typically describe performance in terms of the product DN where D is the diameter (often in mm) of the bearing and N is the rotation rate in revolutions per minute.
Generally there is considerable speed range overlap between bearing types. Plain bearings typically handle only lower speeds, rolling element bearings are faster, followed by fluid bearings and finally magnetic bearings which are limited ultimately by centripetal force overcoming material strength.
[edit] Play
Some applications apply bearing loads from varying directions and accept only limited play or "slop" as the applied load changes. One source of motion is gaps or "play" in the bearing. For example, a 10 mm shaft in a 12 mm hole has 2 mm play.
Allowable play varies greatly depending on the use. As example, a wheelbarrow wheel supports radial and axial loads. Axial loads may be hundreds of newtons force left or right, and it is typically acceptable for the wheel to wobble by as much as 10 mm under the varying load. In contrast, a lathe may position a cutting tool to ±0.02 mm using a ball lead screw held by rotating bearings. The bearings support axial loads of thousands of newtons in either direction, and must hold the ball lead screw to ±0.002 mm across that range of loads.
[edit] Stiffness
A second source of motion is elasticity in the bearing itself. For example, the balls in a ball bearing are like stiff rubber, and under load deform from round to a slightly flattened shape. The race is also elastic and develops a slight dent where the ball presses on it.
The stiffness of a bearing is how the distance between the parts which are separated by the bearing varies with applied load. With rolling element bearings this is due to the strain of the ball and race. With fluid bearings it is due to how the pressure of the fluid varies with the gap (when correctly loaded fluid bearings are typically stiffer than rolling element bearings).
[edit] Life
Fluid and magnetic bearings can potentially give indefinite life. In practice, there are fluid bearings supporting high loads in hydroelectric plants that have been in nearly continuous service since about 1900 and which show no signs of wear.
Rolling element bearing life is determined by load, temperature, maintenance, lubrication, material defects, contamination, handling, installation and other factors. These factors can all have a significant effect on bearing life. For example, the service life of bearings in one application was extended dramatically by changing how the bearings were stored before installation and use, as vibrations during storage caused lubricant failure even when the only load on the bearing was its own weight.[1] Bearing life is statistical: several samples of a given bearing will often exhibit a bell curve of service life, with a few samples showing significantly better or worse life. Bearing life varies because microscopic structure and contamination very greatly even where macroscopically they seem identical.
For plain bearings some materials give much longer life than others. Some of the John Harrison clocks still operate after hundreds of years because of the lignum vitae wood employed in their construction, whereas his metal clocks are seldom run due to potential wear.
Flexure bearings bend a piece of material repeatedly. Some materials fail after repeated bending, even at low loads, but careful material selection and bearing design can make flexure bearing life indefinite.
Although long bearing life is often desirable, it is sometimes not necessary. Harris describes a bearing for a rocket motor oxygen pump that gave several hours life, far in excess of the several tens of minutes life needed.[1]
[edit] Maintenance
Many bearings require periodic maintenance to prevent premature failure, although some such as fluid or magnetic bearings may require little maintenance.
Most bearings in high cycle operations need periodic lubrication and cleaning, and may require adjustment to minimise the effects of wear.
Bearing life is often much better when the bearing is kept clean and well-lubricated. However, many applications make good maintenance difficult. For example bearings in the conveyor of a rock crusher are exposed continually to hard abrasive particles. Cleaning is of little use because cleaning is expensive, yet the bearing is contaminated again as soon as the conveyor resumes operation. Thus, a good maintenance program might lubricate the bearings frequently but clean them never.
[edit] History

The oldest instance of the bearing principle dates to the Egyptians when they used tree trunks under sleds.[2] There are also Egyptian drawings of bearings used with hand drills.[3]
The earliest recovered example of a bearing is a wooden ball bearing supporting a rotating table from the remains of the Roman Nemi ships in Lake Nemi, Italy. The wrecks were dated to 40 AD.[4][5]
Leonardo da Vinci is often credited with drawing the first roller bearing around the year 1500. However, Agostino Ramelli is the first to have published sketches of roller and thrust bearings.[2] An issue with ball bearings is the balls rub against each other, causing additional friction, but rubbing can be prevented by enclosing the balls in a cage. The captured, or caged, ball bearing was originally described by Galileo in the 1600s. The mounting of bearings into a set was not accomplished for many years after that. The first patent for a ball race was by Philip Vaughan of Carmarthen in 1794.
Bearings saw use for holding wheel and axles. The bearings used there were plain bearings that were used to greatly reduce friction over that of dragging an object by making the friction act over a shorter distance as the wheel turned.
The first plain and rolling-element bearings were wood, but ceramic, sapphire, or glass were also used, and steel, bronze, other metals, ceramics, and plastic (e.g., nylon, polyoxymethylene, polytetrafluoroethylene, and UHMWPE) are all common today. A "jeweled" pocket watch uses stones to reduce friction, and allow more precise time keeping. Even old materials can have good durability. As examples, wood bearings can still be seen today in old water mills where the water provides cooling and lubrication.
The first practical caged-roller bearing was invented in the mid-1740s by horologist John Harrison for his H3 marine timekeeper. This uses the bearing for a very limited oscillating motion but Harrison also used a similar bearing in a truly rotary application in a contemporaneous regulator clock.
Friedrich Fischer's idea from the year 1883 for milling and grinding balls of equal size and exact roundness by means of a suitable production machine formed the foundation for creation of an independent bearing industry.
A patent on ball bearings, reportedly the first, was awarded to Jules Suriray, a Parisian bicycle mechanic, on 3 August 1869. The bearings were then fitted to the winning bicycle ridden by James Moore in the world's first bicycle road race, Paris-Rouen, in November 1869.[6]
The modern, self-aligning design of ball bearing is attributed to Sven Wingquist of the SKF ball-bearing manufacturer in 1907, when he was awarded Swedish patent No. 25406 on its design.
Henry Timken, a 19th century visionary and innovator in carriage manufacturing, patented the tapered roller bearing, in 1898. The following year, he formed a company to produce his innovation. Through a century, the company grew to make bearings of all types, specialty steel and an array of related products and services.
Erich Franke invented and patented the wire race bearing in 1934. His focus was on a bearing design with a cross section as small as possible and which could be integrated into the enclosing design. After World War II he founded together with Gerhard Heydrich the company Franke & Heydrich KG (today Franke GmbH) to push the development and production of wire race bearings.
In the early 1980's, Pacific Bearing's founder, Robert Schroeder, invented the first bi-material plane bearing which was size interchangable with linear ball bearings. This bearing had a metal shell (aluminum, steel or stainless steel) and a layer of Teflon-based material connected by a thin adhesive layer. This product is called a "Simplicity Bearing" and the Teflon-based material is known as "Frelon" or "Frelon Gold".
Today, bearings are used in a variety of applications. Ultra high speed bearings are used in dental hand pieces, aerospace bearings are used in the Mars Rover, and flexure bearings are used in optical alignment systems.
[edit] Types
There are many different types of bearings.
Type
Description
Friction
Stiffness
Speed
Life
Notes
Plain bearing
Rubbing surfaces, usually with lubricant; some bearings use pumped lubrication and behave similarly to fluid bearings.
Depends on materials and construction, PTFE has coefficient of friction ~0.05-0.35, depending upon fillers added
Good, provided wear is low, but some slack is normally present
Low to very high
Moderate (depends on lubrication)
Widely used, relatively high friction, suffers from stiction in some applications. Depending upon the application, lifetime can be higher or lower than rolling element bearings.
Rolling element bearing
Ball or rollers are used to prevent or minimise rubbing
Rolling coefficient of friction with steel can be ~0.005 (adding resistance due to seals, packed grease, preload and misalignment can increase friction to as much as 0.125)
Good, but some slack is usually present
Moderate to high (often requires cooling)
Moderate to high (depends on lubrication, often requires maintenance)
Used for higher moment loads than plain bearings with lower friction
Jewel bearing
Off-center bearing rolls in seating
Low
Low due to flexing
Low
Adequate (requires maintenance)
Mainly used in low-load, high precision work such as clocks. Jewel bearings may be very small.
Fluid bearing
Fluid is forced between two faces and held in by edge seal
Zero friction at zero speed, low
Very high
Very high (usually limited to a few hundred feet per second at/by seal)
Virtually infinite in some applications, may wear at startup/shutdown in some cases
Can fail quickly due to grit or dust or other contaminants. Maintenance free in continuous use. Can handle very large loads with low friction and negligible maintenance.
Magnetic bearings
Faces of bearing are kept separate by magnets (electromagnets or eddy currents)
Zero friction at zero speed, but constant power for levitation, eddy currents are often induced when movement occurs, but may be negligible if magnetic field is quasi-static
Low
No practical limit
Indefinite
Often needs considerable power. Maintenance free.
Flexure bearing
Material flexes to give and constrain movement
Very low
Low
Very high
Very high or low depending on materials and strain in application
Limited range of movement, no backlash, extremely smooth motion
†Stiffness is the amount that the gap varies when the load on the bearing changes, it is distinct from the friction of the bearing.
[edit] See also
Ball spline
Combined bearing
Hertz contact stress
Hinge
Main bearing
Needle roller bearing
Pillow block bearing
Race (bearing)
Rolamite
Scrollerwheel
Slewing bearing
Spherical bearing
[edit] References
^ a b Harris, Tedric A. (2000, 4th edition). Rolling Bearing Analysis. Wiley-Interscience. ISBN 0-471-35457-0.
^ a b American Society of Mechanical Engineers (1906), Transactions of the American Society of Mechanical Engineers, 27, American Society of Mechanical Engineers, p. 441, http://books.google.com/books?id=aWd1G50m8WEC&pg=RA1-PA441.
^ Guran, Ardéshir; Rand, Richard H. (1997), Nonlinear dynamics, World Scientific, p. 178, ISBN 9789810229825, http://books.google.com/books?id=ttBQ1k8MYZ4C&pg=PA178&lpg=PA178.
^ Purtell, John (1999/2001). Project Diana, chapter 10: http://nemiship.multiservers.com/nemi.htm
^ Bearing Industry Timeline, http://www.abma-dc.org/BearingIndustry/BearingTimeline/tabid/84/Default.aspx, retrieved 2009-11-17.
^ Bicycle History, Chronology of the Growth of Bicycling and the Development of Bicycle Technology by David Mozer
[edit] External links

Wikimedia Commons has media related to: Bearings
How bearings work
Early bearing failure detection
How to measure a bearing
Kinematic Models for Design Digital Library (KMODDL) - Movies and photos of hundreds of working mechanical-systems models at Cornell University. Also includes an e-book library of classic texts on mechanical design and engineering.
Types of bearings, Cambridge University
Retrieved from "http://en.wikipedia.org/wiki/Bearing_(mechanical)"
Categories: Bearings
Hidden categories: Articles needing additional references from April 2009 All articles needing additional references