WWW.VARDHMANBEARINGS.COM
SPECIAL NOTES
• HFL series has two integral radial bearings arranged on both sides of needle roller clutch. They can therefore support radial forces in particularly space-saving bearing arrangements.
• Plastic springs (HFL...KF) are available for some sizes.
• Partially knurled outer ring (HFL...R) is available upon request.
• A special tool is suggested when assembling the clutch and bearing assembly. For details please contact our engineers.
• Only after the clutch and bearing assembly has been pressed into the hole of the housing, the drawn thin-walled outer ring could then obtain its final dimension and geometric accuracy.
• The transmissible torque and the stresses which can be taken by the housing are subject to the material and the wall thickness of the housing, and such data is needed upon enquiry.
• The clutch and bearing assembly can be normally used in temperature range from -30°C to 120°C. For the working environment above 70°C, oil lubrication is recommended.
ONE WAYBEAR ING DESIGN FEATURES
• Torque can be transmitted by either the housing or the shaft.
• Torque is positively transmitted by rollers that wedge against interior ramps.
• Transition from free motion to lock occurs with minimal backlash or lost motion.
• Available as clutch-only or as a clutch and bearing assembly.
• Clutch-only units should be used with external radial support to hold the shaft and housing.
ONE WAYBEAR ING APPLICATIONS
• Paper moving for copiers, fax machines, paper towel dispensers, etc.
• Exercise equipment
• Appliances
• Two-speed gearboxes
• Rack indexing drives
• Converters, non-return devices and transcendental clutches.
• Fishing Reels, RC Cars, RC Helis, RC Engines
INSPECTION OF ONE WAY BEARINGS
Although the outer cup of the clutch is accurately drawn from strip steel, it can go slightly out of round during heat treat. When the assembly is pressed into a ring gage or properly prepared housing of correct size and wall thickness, it becomes round and properly sized. Direct measurement of the outside diameter of a drawn cup assembly is an incorrect procedure. The proper inspection procedure is as follows:
1. Press the assembly into a ring gage of the proper size as given in the tabular data.
2. Gage the bore with the specified plug gages of the proper size, as given in the tables of dimensions.
- The locking plug is rotated to insure lockup when the clutch is operated at low limit shaft and is mounted in a high limit housing strong enough to properly size the clutch.
- The overrun plug is rotated to ensure free over-running when the clutch is operated on a high limit shaft and is mounted in a low limit housing.
- The go plug and no go plug insure proper size of the bearings in the clutch and bearing assemblies.
INSTALLATION OF ONE WAY BEAR INGS
Simplicity of installation promotes additional cost savings. The drawn cup roller clutch, or the clutch and bearing assembly, must be pressed into its housing. The unit is pressed into the bore of a gear hub or pulley hub, or housing of the proper size, and no shoulders, splines, keys, screws or snap rings are required. Installation procedures are summarized in the following sketches:
Use an arbor press or hydraulic ram press which will exert steady pressure. Never use a hammer or other tool requiring pounding to drive the clutch into its housing.
Make sure that the housing bore is chamfered to permit easy introduction of the clutch and bearing or the clutch unit. Press unit slightly beyond the chamfer in the housing bore to assure full seating. Through-bored housings are always preferred. If the housing has a shoulder, never seat the clutch against the shoulder.
IMPORTANT: The mounted clutch or clutch and bearing assembly engages when the housing is rotated relative to the shaft in the direction of the arrow andLOCK marking stamped on
the cup. Make sure that the unit is oriented properly before pressing it into
its housing.
Use an installation tool as shown in the diagram below. If clutch is straddled by needle roller bearings, press units into position in proper sequence and preferably leave a small clearance between units. When assembling the shaft, it should be rotated in the overrun direction during insertion. The end of the shaft should have a large chamfer or rounding.
SPECIAL NOTES
• HFL series has two integral radial bearings arranged on both sides of needle roller clutch. They can therefore support radial forces in particularly space-saving bearing arrangements.
• Plastic springs (HFL...KF) are available for some sizes.
• Partially knurled outer ring (HFL...R) is available upon request.
• A special tool is suggested when assembling the clutch and bearing assembly. For details please contact our engineers.
• Only after the clutch and bearing assembly has been pressed into the hole of the housing, the drawn thin-walled outer ring could then obtain its final dimension and geometric accuracy.
• The transmissible torque and the stresses which can be taken by the housing are subject to the material and the wall thickness of the housing, and such data is needed upon enquiry.
• The clutch and bearing assembly can be normally used in temperature range from -30°C to 120°C. For the working environment above 70°C, oil lubrication is recommended.
ONE WAYBEAR ING DESIGN FEATURES
• Torque can be transmitted by either the housing or the shaft.
• Torque is positively transmitted by rollers that wedge against interior ramps.
• Transition from free motion to lock occurs with minimal backlash or lost motion.
• Available as clutch-only or as a clutch and bearing assembly.
• Clutch-only units should be used with external radial support to hold the shaft and housing.
ONE WAYBEAR ING APPLICATIONS
• Paper moving for copiers, fax machines, paper towel dispensers, etc.
• Exercise equipment
• Appliances
• Two-speed gearboxes
• Rack indexing drives
• Converters, non-return devices and transcendental clutches.
• Fishing Reels, RC Cars, RC Helis, RC Engines
INSPECTION OF ONE WAY BEARINGS
Although the outer cup of the clutch is accurately drawn from strip steel, it can go slightly out of round during heat treat. When the assembly is pressed into a ring gage or properly prepared housing of correct size and wall thickness, it becomes round and properly sized. Direct measurement of the outside diameter of a drawn cup assembly is an incorrect procedure. The proper inspection procedure is as follows:
1. Press the assembly into a ring gage of the proper size as given in the tabular data.
2. Gage the bore with the specified plug gages of the proper size, as given in the tables of dimensions.
- The locking plug is rotated to insure lockup when the clutch is operated at low limit shaft and is mounted in a high limit housing strong enough to properly size the clutch.
- The overrun plug is rotated to ensure free over-running when the clutch is operated on a high limit shaft and is mounted in a low limit housing.
- The go plug and no go plug insure proper size of the bearings in the clutch and bearing assemblies.
INSTALLATION OF ONE WAY BEAR INGS
Simplicity of installation promotes additional cost savings. The drawn cup roller clutch, or the clutch and bearing assembly, must be pressed into its housing. The unit is pressed into the bore of a gear hub or pulley hub, or housing of the proper size, and no shoulders, splines, keys, screws or snap rings are required. Installation procedures are summarized in the following sketches:
Use an arbor press or hydraulic ram press which will exert steady pressure. Never use a hammer or other tool requiring pounding to drive the clutch into its housing.
Make sure that the housing bore is chamfered to permit easy introduction of the clutch and bearing or the clutch unit. Press unit slightly beyond the chamfer in the housing bore to assure full seating. Through-bored housings are always preferred. If the housing has a shoulder, never seat the clutch against the shoulder.
IMPORTANT: The mounted clutch or clutch and bearing assembly engages when the housing is rotated relative to the shaft in the direction of the arrow andLOCK marking stamped on
the cup. Make sure that the unit is oriented properly before pressing it into
its housing.
Use an installation tool as shown in the diagram below. If clutch is straddled by needle roller bearings, press units into position in proper sequence and preferably leave a small clearance between units. When assembling the shaft, it should be rotated in the overrun direction during insertion. The end of the shaft should have a large chamfer or rounding.
NSK bearings ,
KOYO BEARINGS ,
WWW.ARIHANTENGINEERINGS.COM
ONE WAY CLU TCH BEARINGS
, ONE WAY NEEDLE
BEARINGS , ONE SIDE
ROTATING BEARINGS ,
With the development
of the fully integrated One Way Clutch
Unit, helps two wheeler manufacturers to
reduce assembly time and cost in their processes.
The One Way Clutch Unit is extremely robust and
helps to extend lifecycles compared to conventional designs. The unit can also
be retrofitted to a given application, using the existing mating components.
Manufacturers experience the benefits of a solution that can handle two wheeler
clutch conditions reliably and without making any changes to corresponding
components. For end users, the unit's robust performance and unitized design
offers longer service life and simpler maintenance when necessary.
·
Extended service life
·
Improved reliability
·
Cut assembly costs
·
Reduce assembly times
·
Simplify maintenance
New One Way Bearing series by Boca Bearings. Drawn cup needle
roller clutches have a small radial section height and are also commonly known
as One Way Bearings or Anti-Reverse Bearings. This design uses the same small
radial section as drawn cup needle roller bearings which make better use of available
space. The units are compact, lightweight and operate directly on a shaft; they
are also suitable for transmitting high torque.
One Way
Bearings are designed to transmit torque between the shaft and housing in one
direction and allow free motion in the opposite direction. Proper mounting is
easily accomplished with a simple press fit in the housing. Clutches and clutch
and bearing assemblies are offered both in inch and metric series. One Way
Bearings without bearing assemblies are indicated by suffix: HF/FC/RC. One Way
Bearings with bearing assemblies are indicated by suffix: HFL/FCB/RCB.SPECIAL NOTES
• HFL series has two integral radial bearings arranged on both sides of needle roller clutch. They can therefore support radial forces in particularly space-saving bearing arrangements.
• Plastic springs (HFL...KF) are available for some sizes.
• Partially knurled outer ring (HFL...R) is available upon request.
• A special tool is suggested when assembling the clutch and bearing assembly. For details please contact our engineers.
• Only after the clutch and bearing assembly has been pressed into the hole of the housing, the drawn thin-walled outer ring could then obtain its final dimension and geometric accuracy.
• The transmissible torque and the stresses which can be taken by the housing are subject to the material and the wall thickness of the housing, and such data is needed upon enquiry.
• The clutch and bearing assembly can be normally used in temperature range from -30°C to 120°C. For the working environment above 70°C, oil lubrication is recommended.
ONE WAY
• Torque can be transmitted by either the housing or the shaft.
• Torque is positively transmitted by rollers that wedge against interior ramps.
• Transition from free motion to lock occurs with minimal backlash or lost motion.
• Available as clutch-only or as a clutch and bearing assembly.
• Clutch-only units should be used with external radial support to hold the shaft and housing.
ONE WAY
• Paper moving for copiers, fax machines, paper towel dispensers, etc.
• Exercise equipment
• Appliances
• Two-speed gearboxes
• Rack indexing drives
• Converters, non-return devices and transcendental clutches.
• Fishing Reels, RC Cars, RC Helis, RC Engines
INSPECTION OF ONE WAY BEARINGS
Although the outer cup of the clutch is accurately drawn from strip steel, it can go slightly out of round during heat treat. When the assembly is pressed into a ring gage or properly prepared housing of correct size and wall thickness, it becomes round and properly sized. Direct measurement of the outside diameter of a drawn cup assembly is an incorrect procedure. The proper inspection procedure is as follows:
1. Press the assembly into a ring gage of the proper size as given in the tabular data.
2. Gage the bore with the specified plug gages of the proper size, as given in the tables of dimensions.
- The locking plug is rotated to insure lockup when the clutch is operated at low limit shaft and is mounted in a high limit housing strong enough to properly size the clutch.
- The overrun plug is rotated to ensure free over-running when the clutch is operated on a high limit shaft and is mounted in a low limit housing.
- The go plug and no go plug insure proper size of the bearings in the clutch and bearing assemblies.
INSTALLATION OF ONE WAY B
Simplicity of installation promotes additional cost savings. The drawn cup roller clutch, or the clutch and bearing assembly, must be pressed into its housing. The unit is pressed into the bore of a gear hub or pulley hub, or housing of the proper size, and no shoulders, splines, keys, screws or snap rings are required. Installation procedures are summarized in the following sketches:
Use an arbor press or hydraulic ram press which will exert steady pressure. Never use a hammer or other tool requiring pounding to drive the clutch into its housing.
Make sure that the housing bore is chamfered to permit easy introduction of the clutch and bearing or the clutch unit. Press unit slightly beyond the chamfer in the housing bore to assure full seating. Through-bored housings are always preferred. If the housing has a shoulder, never seat the clutch against the shoulder.
IMPORTANT: The mounted clutch or clutch and bearing assembly engages when the housing is rotated relative to the shaft in the direction of the arrow and
Use an installation tool as shown in the diagram below. If clutch is straddled by needle roller bearings, press units into position in proper sequence and preferably leave a small clearance between units. When assembling the shaft, it should be rotated in the overrun direction during insertion. The end of the shaft should have a large chamfer or rounding.
The OWC -GXZ
One Way Bearing Series are a newly designed compact, light and high performance
unidirectional clutch with an affordable price. These clutches consist of
sintered alloy outer ring, stainless steel roller, leaf spring and welded
shield plate. The OWC
Series has a maximum operating temperature of 194ºF, a compact ...
The EWC One Way Bearing Series consists of a drawn cup roller
clutch, cage and springs. The drawn Cup is made of carburized steel and has a
unique hexed external outer diameter. Housings can be designed in accordance
with the shapes of gears, timing pulleys and cams. Please contact Boca Bearings
direct for custom designed ...
The HF One Way Bearing Series consists of a
drawn cup roller clutch with either single or multi-rollers. An ending
designation or suffix in the part number of KF indicates plastic springs and no
suffix indicates stainless steel springs. Suffix of R indicates a partially
knurled outer ring. Bore sizes are available in a rang ...
 |
More
|
The HFL One Way Bearing Series consists of a
drawn cup roller clutch and bearing assembly with single rollers. An ending
designation or suffix in the part number of KF indicates plastic springs and no
suffix indicates and stainless steel springs. Suffix of R indicates a partially
knurled outer ring. Bore sizes are available ...
|
|
More
|
The HFL One Way Bearing Series consists of a
drawn cup roller clutch and bearing assembly with multi-rollers. An ending
designation or suffix in the part number of KF indicates plastic springs and no
suffix indicates stainless steel springs. Suffix of R indicates a partially
knurled outer ring. Bore sizes are available in a ...
|
|
More
|
The RC One Way Bearing Series consists of a
drawn cup roller clutch with single rollers. An ending designation or suffix in
the part number of FS indicates stainless steel springs and no suffix indicates
plastic springs. Bore sizes are available in a range of 1/8in to 1in. A drawn
cup needle roller clutch has a small radial ...
|
|
More
|
The RCB One Way Bearing Series consists of a
drawn cup roller clutch and bearing assembly with multi-rollers and stainless
steel springs. Bore sizes are available in a range of 3/8in to 1in. A drawn cup
needle roller clutch has a small radial section height and is also commonly
known as a One Way Bearing or Anti-Reverse Bea ...
|
|
More
|
The FC One Way Bearing Series consists of a
drawn cup roller clutch with single rollers and stainless steel springs. Bore
sizes are available in a range of 8mm to 30mm. A drawn cup needle roller clutch
has a small radial section height and is also commonly known as a One Way
Bearing or Anti-Reverse Bearing. One Way Bearings ...
|
|
More
|
The FCB One Way Bearing Series consists of a
drawn cup roller clutch and bearing assembly with multi-rollers and stainless
steel springs. Bore sizes are available in a range of 8mm to 35mm. A drawn cup
needle roller clutch has a small radial section height and is also commonly
known as a One Way Bearing or Anti-Reverse Bear ...
|
|
More
|
The CSK One Way Bearing Series is a sprag type
freewheel integrated into the 6200 radial bearing series. The internal part of
the bearing is protected by a seal but additional seals are recommended
especially when the working temperature exceeds 50ºC. All CSK One Way Bearings
are equipped with chrome formed sprags that incr ...
|
|
More
|
The OWC -GXZ
One Way Bearing Series are a newly designed compact, light and high performance
unidirectional clutch with an affordable price. These clutches consist of
sintered alloy outer ring, stainless steel roller, leaf spring and welded
shield plate. The OWC
Series has a maximum operating temperature of 194ºF, a compact size with a
maximum width of 5.4mm and a very small freewheeling torque. Assembled units
pulley, gear or other mechanical elements are available on request. The OWC-GXZ
One Way Bearing Series has a small radial section height and is also commonly
known as a One Way Bearing or Anti-Reverse Bearing. One Way Bearings are
designed to transmit torque between the shaft and housing in one direction and
allow free motion in the opposite direction.
|
|
||
|
DIMENSION
|
PART #
|
|
|
3 x 7.2000 x 5.4000
|
|
|
|
3 x 7.2000 x 5.4000
|
|
|
|
4 x 10 x 5.4000
|
|
|
|
4 x 10 x 5.4000
|
|
|
|
5 x 11 x 5.4000
|
|
|
|
5 x 11 x 5.4000
|
|
|
|
6 x 12 x 5.4000
|
|
|
|
6 x 12 x 5.4000
|
|
|
|
8 x 14 x 5.4000
|
|
|
|
8 x 14 x 5.4000
|
|
|
|
10 x 16 x 5.4000
|
|
|
|
10 x 16 x 5.4000
|
|
|
|
All One Way Clutch
Bearings (
|
||
The EWC One Way Bearing Series consists of a drawn cup roller
clutch, cage and springs. The drawn Cup is made of carburized steel and has a
unique hexed external outer diameter. Housings can be designed in accordance
with the shapes of gears, timing pulleys and cams. Please contact Boca Bearings
direct for custom designed EWC One Way Bearings. Bore sizes are available in a
range of 4mm to 12mm. A drawn cup needle roller clutch has a small radial
section height and is also commonly known as a One Way Bearing or Anti-Reverse
Bearing. One Way Bearings are designed to transmit torque between the shaft and
housing in one direction and allow free motion in the opposite direction.
|
Metric
|
|
|
|
DIMENSION
|
PART #
|
|
|
4 x 8 x 6
|
EWC0406
|
|
|
6 x 10 x 8
|
EWC0608
|
|
|
8 x 12 x 9
|
EWC0809
|
|
|
8 x 14 x 12
|
EWC0812
|
|
|
10 x 16 x 7
|
EWC1007
|
|
|
10 x 16 x 8
|
EWC1008
|
|
|
10 x 16 x 10
|
EWC1010
|
|
|
10 x 16 x 12
|
EWC1012
|
|
|
12 x 18 x 9
|
EWC1209
|
|
|
12 x 18 x 16
|
EWC1216
|
|
|
12 x 18 x 16
|
1WC1216 (HEX)
|
|
|
All Regular One Way Clutch Bearings (EWC)
|
||
The
HF One Way Bearing Series consists of a drawn cup roller clutch with either
single or multi-rollers. An ending designation or suffix in the part number of
KF indicates plastic springs and no suffix indicates stainless steel springs.
Suffix of R indicates a partially knurled outer ring. Bore sizes are available
in a range of 6mm to 35mm. A drawn cup needle roller clutch has a small radial
section height and is also commonly known as a One Way Bearing or Anti-Reverse
Bearing. One Way Bearings are designed to transmit torque between the shaft and
housing in one direction and allow free motion in the opposite direction.
|
Metric
|
|
|
|
DIMENSION
|
PART #
|
|
|
3 x 6.5 x 6
|
HF0306 KF
|
|
|
3 x 6.5 x 6
|
HF0306 KF R
|
|
|
4 x 8 x 6
|
HF0406
|
|
|
4 x 8 x 6
|
HF0406 KF
|
|
|
4 x 8 x 6
|
HF0406 KF R
|
|
|
6 x 10 x 8
|
HF0608
|
|
|
6 x 10 x 12
|
HF0612
|
|
|
6 x 10 x 12
|
HF0612 KF
|
|
|
6 x 10 x 12
|
HF0612 KF R
|
|
|
6 x 10 x 12
|
HF0612 R
|
|
|
8 x 12 x 12
|
HF0812
|
|
|
8 x 12 x 12
|
HF0812 KF
|
|
|
8 x 12 x 12
|
HF0812 KF R
|
|
|
8 x 12 x 12
|
HF0812 R
|
|
|
10 x 14 x 8
|
HF1008
|
|
|
10 x 14 x 12
|
HF1012
|
|
|
10 x 14 x 12
|
HF1012 KF
|
|
|
10 x 14 x 12
|
HF1012 KF R
|
|
|
12 x 18 x 16
|
HF1216
|
|
|
14 x 20 x 16
|
HF1416
|
|
|
16 x 22 x 16
|
HF1616
|
|
|
18 x 24 x 16
|
HF1816
|
|
|
20 x 26 x 16
|
HF2016
|
|
|
25 x 32 x 20
|
HF2520
|
|
|
30 x 37 x 20
|
HF3020
|
|
|
All Regular One Way Clutch Bearings (HF)
|
||
The HFL One Way Bearing Series consists of a drawn cup roller
clutch and bearing assembly with single rollers. An ending designation or suffix
in the part number of KF indicates plastic springs and no suffix indicates and
stainless steel springs. Suffix of R indicates a partially knurled outer ring.
Bore sizes are available in a range of 3mm to 8mm. A drawn cup needle roller
clutch has a small radial section height and is also commonly known as a One
Way Bearing or Anti-Reverse Bearing. One Way Bearings are designed to transmit
torque between the shaft and housing in one direction and allow free motion in
the opposite direction.
|
Metric
|
|
|
|
DIMENSION
|
PART #
|
|
|
3 x 6.5 x 8
|
HFL0308 KF
|
|
|
3 x 6.5 x 8
|
HFL0308 KFR
|
|
|
4 x 8 x 8
|
HFL0408 KF
|
|
|
4 x 8 x 8
|
HFL0408 KFR
|
|
|
6 x 10 x 6
|
HFL0606 KFR
|
|
|
6 x 10 x 15
|
HFL0615
|
|
|
6 x 10 x 15
|
HFL0615 KF
|
|
|
6 x 10 x 15
|
HFL0615 KFR
|
|
|
6 x 10 x 15
|
HFL0615 R
|
|
|
8 x 12 x 6
|
HFL0806 KFR
|
|
|
All Regular One Way Clutch & Plain Bearing Assembly
(HFL)
|
||
The HFL One Way Bearing Series consists of a drawn cup roller
clutch and bearing assembly with multi-rollers. An ending designation or suffix
in the part number of KF indicates plastic springs and no suffix indicates
stainless steel springs. Suffix of R indicates a partially knurled outer ring.
Bore sizes are available in a range of 8mm to 35mm. A drawn cup needle roller
clutch has a small radial section height and is also commonly known as a One
Way Bearing or Anti-Reverse Bearing. One Way Bearings are designed to transmit
torque between the shaft and housing in one direction and allow free motion in
the opposite direction.
|
Metric
|
|
|
|
DIMENSION
|
PART #
|
|
|
8 x 12 x 22
|
HFL0822
|
|
|
8 x 12 x 22
|
HFL0822 KF
|
|
|
8 x 12 x 22
|
HFL0822 R
|
|
|
10 x 14 x 22
|
HFL1022
|
|
|
12 x 18 x 26
|
HFL1226
|
|
|
14 x 20 x 26
|
HFL1426
|
|
|
16 x 22 x 26
|
HFL1626
|
|
|
18 x 24 x 26
|
HFL1826
|
|
|
20 x 26 x 26
|
HFL2026
|
|
|
25 x 32 x 30
|
HFL2530
|
|
|
30 x 37 x 30
|
HFL3030
|
|
|
35 x 42 x 30
|
HFL3530
|
|
|
All Regular One Way Clutch & Roller Bearing Assembly
(HFL)
|
||
The RC One Way Bearing Series consists of a drawn cup roller
clutch with single rollers. An ending designation or suffix in the part number
of FS indicates stainless steel springs and no suffix indicates plastic
springs. Bore sizes are available in a range of 1/8in to 1in. A drawn cup
needle roller clutch has a small radial section height and is also commonly
known as a One Way Bearing or Anti-Reverse Bearing. One Way Bearings are
designed to transmit torque between the shaft and housing in one direction and
allow free motion in the opposite direction.
|
|
||
|
DIMENSION
|
PART #
|
|
|
0.1250 x 0.2810 x
0.2500
|
RC02
|
|
|
0.2500 x 0.4375 x 0.5000
|
RC040708
|
|
|
0.3750 x 0.6250 x 0.5000
|
RC061008
|
|
|
0.3750 x 0.6250 x 0.5000
|
RC061008 FS
|
|
|
0.5000 x 0.7500 x 0.5000
|
RC081208
|
|
|
0.5000 x 0.7500 x 0.5000
|
RC081208 FS
|
|
|
0.6250 x 0.8750 x 0.6250
|
RC101410
|
|
|
0.6250 x 0.8750 x 0.6250
|
RC101410 FS
|
|
|
0.7500 x 1.0000 x 0.6250
|
RC121610
|
|
|
0.7500 x 1.0000 x 0.6250
|
RC121610 FS
|
|
|
1.0000 x 1.3100 x 0.6250
|
RC162110
|
|
|
1.0000 x 1.3130 x 0.6250
|
RC162110 FS
|
|
|
All Regular One Way Clutch (RC) One Way Clutch Bearings
Inch Sizes
|
||
The RCB One Way Bearing Series consists of a drawn cup roller
clutch and bearing assembly with multi-rollers and stainless steel springs.
Bore sizes are available in a range of 3/8in to 1in. A drawn cup needle roller
clutch has a small radial section height and is also commonly known as a One
Way Bearing or Anti-Reverse Bearing. One Way Bearings are designed to transmit
torque between the shaft and housing in one direction and allow free motion in
the opposite direction.
|
Inch
|
|
|
|
DIMENSION
|
PART #
|
|
|
0.3750 x 0.6250 x 0.8750
|
RCB061014
|
|
|
0.3750 x 0.6250 x 0.8750
|
RCB061014 FS
|
|
|
0.5000 x 0.7500 x 0.8750
|
RCB081214
|
|
|
0.5000 x 0.7500 x 0.8750
|
RCB081214 FS
|
|
|
0.6250 x 0.8750 x 1.0000
|
RCB101416
|
|
|
0.6250 x 0.8750 x 1.0000
|
RCB101416 FS
|
|
|
0.6250 x 0.8750 x 21.6600
|
RCB101416 FS
|
|
|
0.7500 x 1.0000 x 1.0000
|
RCB121616
|
|
|
0.7500 x 1.0000 x 1.0000
|
RCB121616 FS
|
|
|
1.0000 x 1.3130 x 1.0630
|
RCB162117
|
|
|
1.0000 x 1.3130 x 1.0630
|
RCB162117 FS
|
|
|
All Regular One Way Clutch & Roller Bearing Assembly
(RCB) One Way Clutch Bearings Inch Sizes
|
||
The FC One Way Bearing Series consists of a drawn cup roller
clutch with single rollers and stainless steel springs. Bore sizes are
available in a range of 8mm to 30mm. A drawn cup needle roller clutch has a
small radial section height and is also commonly known as a One Way Bearing or
Anti-Reverse Bearing. One Way Bearings are designed to transmit torque between
the shaft and housing in one direction and allow free motion in the opposite
direction.
|
Metric
|
|
|
|
DIMENSION
|
PART #
|
|
|
10 x 16 x 12
|
FC10
|
|
|
12 x 18 x 16
|
FC12
|
|
|
16 x 22 x 16
|
FC16
|
|
|
20 x 26 x 16
|
FC20
|
|
|
25 x 32 x 20
|
FC25
|
|
|
30 x 37 x 20
|
FC30
|
|
|
All Regular One Way Clutch w/ Roller,Stainless Steel
Spring (FC) One Way Clutch Bearings Metric Sizes
|
||
The FCB One Way Bearing Series consists of a drawn cup roller
clutch and bearing assembly with multi-rollers and stainless steel springs.
Bore sizes are available in a range of 8mm to 35mm. A drawn cup needle roller
clutch has a small radial section height and is also commonly known as a One
Way Bearing or Anti-Reverse Bearing. One Way Bearings are designed to transmit
torque between the shaft and housing in one direction and allow free motion in
the opposite direction.
|
Metric
|
|
|
|
DIMENSION
|
PART #
|
|
|
8 x 14 x 20
|
FCB8
|
|
|
10 x 16 x 20
|
FCB10
|
|
|
12 x 18 x 260
|
FCB12
|
|
|
16 x 22 x 26
|
FCB16
|
|
|
20 x 26 x 26
|
FCB20
|
|
|
25 x 32 x 30
|
FCB25
|
|
|
30 x 37 x 30
|
FCB30
|
|
|
All Regular One Way Clutch & Roller Bearing Assembly
(FCB)
|
||
The CSK One Way Bearing Series is a sprag type freewheel
integrated into the 6200 radial bearing series. The internal part of the bearing
is protected by a seal but additional seals are recommended especially when the
working temperature exceeds 50ºC. All CSK One Way Bearings are equipped with
chrome formed sprags that increases the over-run life several times. Torque
transmission is ensured by a press fit assembly into a rigid outer housing and
onto a shaft with an N6 tolerance. Initial bearing radial clearance is set at
C5 and is reduced if using the press fit as specified.
The CSK One
Way Bearing Series has a small radial section height and is also commonly known
as a One Way Bearing or Anti-Reverse Bearing. One Way Bearings are designed to
transmit torque between the shaft and housing in one direction and allow free
motion in the opposite direction. In addition to the basic CSK model, type
CSK..P features a keyway on the inner race and CSK..PP features a keyway on
both the inner and outer race. For this reason it can be keyed to a shaft.|
Metric
|
|
|
|
DIMENSION
|
PART #
|
|
|
8 x 22 x 9
|
CSK8
|
|
|
8 x 22 x 9
|
CSK8P
|
|
|
12 x 32 x 10
|
CSK201
|
|
|
12 x 32 x 10
|
CSK201P
|
|
|
15 x 35 x 11
|
CSK202
|
|
|
15 x 35 x 11
|
CSK202P
|
|
|
15 x 35 x 11
|
CSK202PP
|
|
|
15 x 35 x 16
|
CSK202-2RS
|
|
|
15 x 35 x 16
|
CSK202P-2RS
|
|
|
17 x 40 x 12
|
CSK203
|
|
|
17 x 40 x 12
|
CSK203P
|
|
|
17 x 40 x 12
|
CSK203PP
|
|
|
17 x 40 x 17
|
CSK203-2RS
|
|
|
17 x 40 x 17
|
CSK203P-2RS
|
|
|
20 x 47 x 14
|
CSK204
|
|
|
20 x 47 x 14
|
CSK204P
|
|
|
20 x 47 x 14
|
CSK204PP
|
|
|
20 x 47 x 19
|
CSK204-2RS
|
|
|
20 x 47 x 19
|
CSK204P-2RS
|
|
|
25 x 52 x 15
|
CSK205
|
|
|
25 x 52 x 15
|
CSK205P
|
|
|
25 x 52 x 15
|
CSK205PP
|
|
|
25 x 52 x 20
|
CSK205-2RS
|
|
|
25 x 52 x 20
|
CSK205P-2RS
|
|
|
30 x 62 x 16
|
CSK206
|
|
|
All Sprag Type One Way Clutch Bearing (CSK) One Way Clutch
Bearings Metric Sizes
|
||
New One Way Bearing series by Boca Bearings. Drawn cup needle
roller clutches have a small radial section height and are also commonly known
as One Way Bearings or Anti-Reverse Bearings. This design uses the same small
radial section as drawn cup needle roller bearings which make better use of
available space. The units are compact, lightweight and operate directly on a
shaft; they are also suitable for transmitting high torque.
One Way
Bearings are designed to transmit torque between the shaft and housing in one
direction and allow free motion in the opposite direction. Proper mounting is
easily accomplished with a simple press fit in the housing. Clutches and clutch
and bearing assemblies are offered both in inch and metric series. One Way
Bearings without bearing assemblies are indicated by suffix: HF/FC/RC. One Way
Bearings with bearing assemblies are indicated by suffix: HFL/FCB/RCB.SPECIAL NOTES
• HFL series has two integral radial bearings arranged on both sides of needle roller clutch. They can therefore support radial forces in particularly space-saving bearing arrangements.
• Plastic springs (HFL...KF) are available for some sizes.
• Partially knurled outer ring (HFL...R) is available upon request.
• A special tool is suggested when assembling the clutch and bearing assembly. For details please contact our engineers.
• Only after the clutch and bearing assembly has been pressed into the hole of the housing, the drawn thin-walled outer ring could then obtain its final dimension and geometric accuracy.
• The transmissible torque and the stresses which can be taken by the housing are subject to the material and the wall thickness of the housing, and such data is needed upon enquiry.
• The clutch and bearing assembly can be normally used in temperature range from -30°C to 120°C. For the working environment above 70°C, oil lubrication is recommended.
ONE WAY
• Torque can be transmitted by either the housing or the shaft.
• Torque is positively transmitted by rollers that wedge against interior ramps.
• Transition from free motion to lock occurs with minimal backlash or lost motion.
• Available as clutch-only or as a clutch and bearing assembly.
• Clutch-only units should be used with external radial support to hold the shaft and housing.
ONE WAY
• Paper moving for copiers, fax machines, paper towel dispensers, etc.
• Exercise equipment
• Appliances
• Two-speed gearboxes
• Rack indexing drives
• Converters, non-return devices and transcendental clutches.
• Fishing Reels, RC Cars, RC Helis, RC Engines
INSPECTION OF ONE WAY BEARINGS
Although the outer cup of the clutch is accurately drawn from strip steel, it can go slightly out of round during heat treat. When the assembly is pressed into a ring gage or properly prepared housing of correct size and wall thickness, it becomes round and properly sized. Direct measurement of the outside diameter of a drawn cup assembly is an incorrect procedure. The proper inspection procedure is as follows:
1. Press the assembly into a ring gage of the proper size as given in the tabular data.
2. Gage the bore with the specified plug gages of the proper size, as given in the tables of dimensions.
- The locking plug is rotated to insure lockup when the clutch is operated at low limit shaft and is mounted in a high limit housing strong enough to properly size the clutch.
- The overrun plug is rotated to ensure free over-running when the clutch is operated on a high limit shaft and is mounted in a low limit housing.
- The go plug and no go plug insure proper size of the bearings in the clutch and bearing assemblies.
INSTALLATION OF ONE WAY B
Simplicity of installation promotes additional cost savings. The drawn cup roller clutch, or the clutch and bearing assembly, must be pressed into its housing. The unit is pressed into the bore of a gear hub or pulley hub, or housing of the proper size, and no shoulders, splines, keys, screws or snap rings are required. Installation procedures are summarized in the following sketches:
Use an arbor press or hydraulic ram press which will exert steady pressure. Never use a hammer or other tool requiring pounding to drive the clutch into its housing.
Make sure that the housing bore is chamfered to permit easy introduction of the clutch and bearing or the clutch unit. Press unit slightly beyond the chamfer in the housing bore to assure full seating. Through-bored housings are always preferred. If the housing has a shoulder, never seat the clutch against the shoulder.
IMPORTANT: The mounted clutch or clutch and bearing assembly engages when the housing is rotated relative to the shaft in the direction of the arrow and
Use an installation tool as shown in the diagram below. If clutch is straddled by needle roller bearings, press units into position in proper sequence and preferably leave a small clearance between units. When assembling the shaft, it should be rotated in the overrun direction during insertion. The end of the shaft should have a large chamfer or rounding.
- One Way Bearing Shaft Tolerance Chart
- One Way Bearing Catalog
|
|
|
|
|
|
|
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The Functions of clutches
Indexing / Feeding : is to convert motion either from a
continuously rotating shaft on intermittent basis OR by converting the
reciprocating linear motion of a Pneumatic / Hydraulic cylinder into an
intermittent rotary motiion.The rotary motion of the drive shaft is converted
into an intermittent rotary motion by means of a hold pin and connecting rod
attached to arm of the freewheel whose arc of index can be varied as required
by adjusting slot. Especially when clutch is used as a indexing clutch, the Key
connections must be free from play. The best indexing application is reached
with unalloyed oils with a low degree of viscosity.
Overrunning: The inner ring can rotate faster then the
outer ring in same direction of input and if stopped inner ring continues to
rotate of input and if stopped inner ring continues to rotate at input speed
and vice versa. E.g. if a large motor or turbine has to be up to speed,
by a slow speed starter motor, the use of freewheel between these elements
enables the starter motor to be shut down without any mechanical involvement.
If a freewheel is interposed in a drive between a gearbox / a large machine,
the freewheel prevents any back drive OR damage to gearbox if at all any power
failure. In this function, if the direction force / rotation changes, there
will be automatic obstruction of connection between the component(s) and
coupled machine.
Backstopping / Holdback: The Purpose of backstopping is to providing a return OR reverse lock. This smoothly permits rotation of the drive shaft by overrunning in one direction but immediately locks if the shaft by attempts to go on reverse, such as in inclined conveyors, elevators etc. in case of power failure OR motor is switched off, to avoid the conveyor load from running back.
Lubrication: Most clutches especially indexing and clutches with high speed overrunning are provided with unalloyed, acid free, low viscosity oil. Oil must be changed initially after about 80 operating hours & there after approximately 1500 operating hours .depending on the environment, refilling up to 1/3 level.
Backstopping / Holdback: The Purpose of backstopping is to providing a return OR reverse lock. This smoothly permits rotation of the drive shaft by overrunning in one direction but immediately locks if the shaft by attempts to go on reverse, such as in inclined conveyors, elevators etc. in case of power failure OR motor is switched off, to avoid the conveyor load from running back.
Lubrication: Most clutches especially indexing and clutches with high speed overrunning are provided with unalloyed, acid free, low viscosity oil. Oil must be changed initially after about 80 operating hours & there after approximately 1500 operating hours .depending on the environment, refilling up to 1/3 level.
Applications: in all industries: Agricultural Machines - Fertilizer
spreaders, Straw Presses, Feed Cutters, Tractor Distribution Gear, Plant
Sprayers)Air craft - Power Transmission unit, Generator Construction- Cement
Mixtures, Barrel Mills, Drilling Rigs) Drying - Furnaces, continuous Ovens.
Food - Bottling Corking & dosing Machines, General Drives- Electric Motors,
Worm Drive gearbox, Hoisting & Conveying Device - Elevator Drive, Bucket
Conveyor, Screw Pumps, Leather - Tanning & Curing, Drying & Sewing,
Machine Tools - Presses & Shapers. Packaging, Paper & Printing - Tube
filling, Wrapping , Labeling, Paper Production, Inking & Feed Rollers.
Power Plant: Turbine Starter, Blower, Pumps & Compressors: Vacuum Pumps ,
Turbo Compressors, Rubber & Plastic: Injection Moulding Textile - Blow Room
-Machinery : Double rib & Jacquard loom, Circular & flush stitch
machines, Wire processing, Fishing Net Machinery.
We also stock
imported one way
clutch bearings like
STIEBER germany , TSUBAKI BEARING , SKF BEAR ING , NTN BEARING ,
INA BEARING , SBI
BEARING , IKO BEAR ING ,
No comments:
Post a Comment